Skip to content

1 of 2

Victron Energy – MultiPlus 12/3000/120-50 120V VE.Bus (UL) – PMP122301102

£1,330.44 INC. VAT (£1,108.70 EXC. VAT)
£1,330.44 INC. VAT (£1,108.70 EXC. VAT)
Regular price
£1,330.44 INC. VAT (£1,108.70 EXC. VAT)
Sale price
£1,330.44 INC. VAT (£1,108.70 EXC. VAT)
Pop-up link text
Victron Energy – MultiPlus 12/3000/120-50 120V VE.Bus (UL) – PMP122301102-Powerland

Multifunctional, with intelligent power management.

The MultiPlus is a powerful true sine wave inverter, a sophisticated battery charger that features adaptive charge technology, and a high speed AC transfer switch in a single compact enclosure. Next to these primary functions, the MultiPlus ha several advanced features, as outlined below.

Two AC Outputs

The main output has no-break functionality. The MultiPlus takes over the supply to the connected loads in the event of a grid failure or when shore/generator power is disconnected. This happens so fast (less than 20 milliseconds) that computers and other electronic equipment will continue to operate without disruption. The second output is live only when AC is available on the input of the MultiPlus. Loads that should not discharge the battery, like a water heater for example, can be connected to this output (second output available on the models rated at 3kVA and more).

Virtually unlimited power thanks to parallel operation

Up to six Multis can operate in parallel to achieve higher power output. Six 24/3000/70 units. for example, provide 15kW / 18kVA output power with 420 Amps of charging capacity.

Three phase capability

In addition to parallel connection, three units can be configured for three-phase output. But that’s not all: with three strings of six parallel units a 45 kW / 54kVA three phase inverter and 1260A charger can be built.

Split phase options

Two units can be stacked to provide 120-0-120V, and additional units can be paralleled up to a total of 6 units per phase, to supply up to 30kW / 36kVA of split phase power. Alterntively, a split phase AC can be obtained by connecting our autotransformer (see data sheet on to a ‘European’ inverter programmed to supply 240V / 60Hz.

PowerControl – Dealing with limited generator, shore side or generator power

The MultiPlus is a very powerful battery charger. It will therefore draw a lot of current from the generator or shore side supply (nearly 20A per 3kVA MultiPlus at 120VAC). With the MultiPlus Control Panel a maximum generator or shore current can be set. The MultiPlus will then take account of other AC loads and use whatever is extra for charging, thus preventing the generator or shore supply from being overloaded.

PowerAssist – Boosting the capacity of shore or generator power

This feature takes the principle of PowerControl to a further dimension. It allows the MultiPlus to supplement the capacity of the alternative source. Where peak power is so often required only for a limited period, the MultiPlus will make sure that insufficent shore or generator power is immediately compensated for by power from the battery. When the load reduces, the spare power is used to recharge the battery.

Four stage adaptive charger and dual bank battery charging

The main output provides a powerful charge to the battery system by means of advacned ‘adaptive charge’ software. The software fine-tunes the three stage automatic process to suit the condition of the battery, and adds a fourth stage for long periods of float charging. The adaptvie charge process is described in more detailes on the Phoenix Charger datasheet and on our website, under Technical Information. In addition to this, the MultiPlus will charge a second battery using an independent trickle charge output intended for a main engine or generator starter battery.

System configuring has never been easier

After installation, the MultiPlus is ready to go.
If settings have to be changed, this can be done in a matter of minutes with a DIP switch setting procedure. Even parallel and 3-phase operation can be programmed with DIP switches: no computer needed!
Alternatively, VE.Net can be used instead of the DIP switches. And sophisticated software (VE.Bus Quick COnfigure and VE.Bus System Configurator) is available to configure several new, advanced features.

Manufacturer: Victron Energy
Part Number: PMP122301102
Weight: 19kg
Length: 218mm
Width: 258mm
Height: 362mm
Input Voltage: 9.5 – 17 V
Output Voltage:
Continuous Output Power: 2400W at 25°C
Peak Output Power: 6000W
Charger Output Current: 120A
Transfer Switch: 120A
Frequency: 60Hz
Operating Temperature Range: -40 to +65°C (fan assisted cooling)
Output Wave Form: Pure Sine Wave
Warranty: 5 Years